From at least 1991 onward, all S10 Blazers and Jimmies came with 4 wheel as standard equipment. When adding weight, it is important to consider the manufacturer specifications, which state that the total gross weight of the 2003 Chevy S10 should not exceed 4,200 pounds, including any additional equipment or loads. Maximum Loaded Trailer Weight lbs. Weight and weight limits for other models can be found in the owners manual or directly from the manufacturer. When replacing, be carefull not to cross-thread the transmission lines. Slightly jack engine up, you dont need a whole lot like maybe an inch at most. Clean connectors where light bulbs are making sure each touch.
Carefully lift straight up and out. It used the same engines and had many of the same upgrades as the Bravada. Heating the end caps with a torch will force the glue out of the side … weep holes where it was injected. Power output was increased to 160 hp 120 kW in 1989. The long cargo bed has the same depth and width, but its length is extended to 88. The electronic transfer-case added luxury however there was no neutral position with the electronic transfer case, so the owner's manual stated that the drive shaft had to be removed when the vehicle was being towed.
I could pull it 60 m … ph but had to slow way way down before I came to a turn or corner and dirt roads were even worse. Pull digital display out from bottom raising and top pulling. Remove the pin holding the cable to the heating assembly and pop out the red tab to remove the cable assembly from the heating unit. The S-10 Blazer and S-15 Jimmy were based on the and pickup trucks and were manufactured in ; ; ; ; , , Canada; , Canada; and ,. A passenger airbag is now standard. Located under the Dash-board, inside the Passenger Compartment.
The redesigned 1994 S-10 and Sonoma pickups used R134a refrigerant. Loosen intake hose clamp, Loosen the two wing nuts on the plastic part of the air intake atached to the top of the radiator and remove. Since the crew cab has four doors, its cargo bed has the smallest size when compared to other cab sizes. You'll probably hear an air sound out your exhaust system. Refill coolant, let engine idling warm up, check coolant again and the installed heater plug for leaks.
. Once you have the lines and wires of the fuel pump you can remove the tank. Depends on engine size but if you have the common 2. In 1998, the interior and exterior received some cosmetic changes. In the retail sales of two-door Blazer models ended in 2004; all other models were sold until April 20, 2005. Also look on the intak … e manifold.
To celebrate the 30th anniversary of the Jimmy nameplate, the Jimmy Diamond Edition was launched. The 1994 S-10 Blazer and Jimmy seem to have used R-12 until the end of their production run and subsequent replacement with redesigned 1995 models that looked like new-for-1994 pickups. The weight of a Chevrolet S10 pickup truck varies depending on the specific model. Another upscale model was the 1998. Loosen the two transmission lines.
For the 2001 model year, the truck received a new center console. While load weight limits vary from state to state, the manufacturer places its own load limit on the vehicle, meaning that the truck should not tow any more than that specified amount. The crew cab model comes with four doors and can seat four to five passengers. This sub-model lasted until 2004. The second-generation Blazer was officially sold in Taiwan, between 1995 and 1996.
This was phased in because of the L35 option which used a similar fuel line setup. Reinsall Drive Shaft to markings. This is a little easier than removing theexhaust manif … old and taking a chance on breaking a bolt off in theblock. Disconnect Cat from exhaust system closest to engine and try running the engine. Regular Cab SuperCab 4x2 4x4 4x2 4x4 4. At the same time, a Blazer Xtreme only on the 2-door model was added to the lineup, based on the S10 Xtreme. Regular Cab SuperCab SuperCrew 4x2 4x4 4x2 4x4 4x2 4x4 4.