Picture is for illustration purposes only Make: Chevrolet Model: S10 Blazer Sub Models: Base Engine Sizes: 2. If you do … not have one, I suggest you get one. I would say to look in your Owner's Guide or Manual to find better detailed instructions. The Modified Life staff has taken all its Chevrolet car radio wiring diagrams, Chevrolet car stereo wiring diagrams, Chevrolet car radio wiring schematics, Chevrolet car wiring diagrams and cataloged them online. While either the hour or the minute numbers are flashing, turn the f knob, located on the upper right side of the radio, clockwise or counterclockwise to increase or decrease the time. Power on or off, radio on or off.
After all, it could be an electrical issue inside your cd player. To change the time default setting from 12 hour to 24 hour, press the H button and then the pushbutton located under the forward arrow label. I would remove your radio and check the wiring. Radio unit is all buttons with a digital readout. While the radio is turned off, push the set button one time.
Here are the instructions for both. The minutes on the clock will begin to increment slowly. If you Cavalier has a set button, hold it down and while the set light is on use the seek and scan buttons to set the clock. When the minutes reach 59 they wrap around to 0 and then keep on incrementing. If there's no evidence of faulty wiring then try a new cd player. The time can be set with the ignition on or off. Press the H button until the hour begins flashing on the display.
Press the clock button again until the clock display stops flashing to set the currently displayed time; otherwise, the flashing will stop after five seconds and the current time displayed will be automatically set. To set the clock on a 1996 Silverado: turn the radio off; there are two small buttons below the clock, one says hours and one says minutes. I used this about 3 years ago still holding. Every time the pushbutton is pressed again, the time or the date if selected, will increase by one. Driving home I spent about 40 minutes of the drive from the dealership trying to figure out h … ow to get the proper time on the clock as I drove, pressing each and every button and holding it down to no avail. Keep holding down the button until the correct minute is reached. Within five seconds, press and hold the.
To change the time default setting from 12 hour to 24 hour, press the clock button and then the pushbutton located under the forward arrow label. If your clock is showing the wrong time, all you need to do is enter the radio's clock-setting mode to correct the time and set the clock. The date will not automatically display. I add this because I had a tough time finding the answer for my model year. Setting the Clock on the 2001 Chevy Prizm.
The minutes will begin to blink. This gives you more control over setting the hour or minute, and it helps you avoid going past your desired time. All our Chevrolet S10 Pickup parts and engines are checked for performance and exterior defects. You will see whether your Chevrolet needs to be turned on and how to navigate to the clock settings and accurately set the time in this free how-to video for a 1996 Chevrolet S10. Depending on which radio you have, you either turn the radio off, push the clock button, then advance the time with the seek or tune button - or - push the clock button and put the time in using the number buttons then push the clock button again to store the setting. You have to continue pressing the hour or minute button until the hour or minute wraps all the way around and comes back to the time you want. Chevy S-series vehicles such as the S-10 feature a handy digital clock located on the vehicle's audio systems panel.
If nothing else, take the seat to an upholstry shop that specializes in automobile interiors. Dealer can order you one or you may find one at a salvage yard. Below is the generic clock set proceedure for the most popular radio at that time. The hours on the clock will begin to increment slowly. When time is set push set button again, then turn radio on.
The date with display will time out after a few seconds and go back to the normal radio and time display. To set the time and date, follow these instructions: 1. Sounds to me like you've got a fualty radio. You can set the time by following these steps: 1. Once the time 12H and 24H are displayed, press the pushbutton located under the desired option to select the default. I will also add that you only need press and hold for a moment, the time colon will begin flashing. I really don'tknow your truck year, but it sounds like a earlier model, say early90's! To set the minutes, press the clock button again.
This type information can be easily found in your owner's manual. Hope this solve your dilemma. Press the button a second time and the minute begins flashing on the display. Once the time 12H and 24H are displayed, press the pushbutton located under the desired option to select the default. While either the hour or the minute numbers are flashing, turn the tune knob, located on the upper right side of the radio, clockwise or counterclockwise to increase or decrease the time.